V34光學級混合劑屬於中型產品,能夠復修車漆上較輕微瑕疵,並在超硬油漆面上填補缺憾,最後為車身拋光作結尾! V34 Optical Grade Hybrid Compound is the mid-grade compound that eliminates light to moderate paint defects and imperfections from super hard paints, then finishes like a fine polish.

Product Details


  • 快速去除1500-2000磨蝕粒子造成的痕跡
  • 去除中等程度漩渦痕跡、刮痕、氧化和其他缺陷
  • 為下一個優化步驟做好準備
  • 復修車頭燈,讓您在晚上安全駕駛
  • 減少清潔塵埃,帶來最佳拋光體驗








1. 搖勻拋光劑,在墊上塗上4-5滴
2. 在墊上加上柔順劑後,每次以61cm² 面積塗抹車身
3. 把拋光機力度調至1,以確保塗層均勻
4. 把拋光機力度調至5-6,配合適度壓力,來回擦拭表面2-3次
5. 用拋光機輕力擦拭表面,以作飾面
6. 用超細纖維毛巾清除表面殘留物
7. 請注意:使用產品前請先在一角測試產品效果

1. 搖勻拋光劑,在墊上塗上4-5滴
2. 在墊上加上柔順劑後,每次以61cm² 面積塗抹車身
3. 帶拋光機遠離車身,然後把力度調至1000-1500rpms
4. 不加壓力地來回擦拭表面3-4次,以混和塗層
5. 把拋光機力度調至1200-1800rpms,再次擦拭以作飾面
6. 擦拭至表面光亮清晰
7. 用超細纖維毛巾清除表面殘留物


Use This Compound To: 

  • Quickly remove 1500-2000 grit sanding marks
  • Remove moderate swirls, scratches, oxidation, and paint defects
  • Get the perfect base for next steps
  • Restore your headlights for safest night driving
  • Minimize dusting for the best polishing experience

Mid-Level Cutting & Finishing Power For Tough Paint Defects

V34 cuts away light to moderate swirls, scratches, oxidation, and wet sand marks. V34 is blended with optical-grade micro abrasives that remove paint imperfections and defects, then finish with the clarity and precision that perfectionists demand. The diminishing micro abrasives work fast with true-cut accuracy; there are no fillers, so the results you see are the true results you get. 

Optical Grade Micro Abrasive Technology For Enhanced Clarity

V34 is the preferred cutting compound for lightly oxidized optical plastic and is the perfect one step polish to finish after wet-sanding faded and hazy headlights. The water-based formula is blended with advanced lubricants for extended work time. Use V34 with any dual action or rotary polisher to remove scratches and surface defects and restore luster and shine to any paint finish!

<How to Use>
Dual Action Polisher

1.Shake well and apply 4-5 drops to desired pad. 
2.Prime pad with Pad Conditioner. Dab product out evenly across 2' x 2' section. 
3.Turn on machine on paint to speed setting 1 to spread product. 
4.Increase speed to 5-6 and using moderate pressure, work area in 2-3 passes until product becomes clear.
5.Follow with light pressure to finish. 
6.Remove residue with a clean microfiber towel.
7.Please Note: Always try a test spot before use.

Rotary Polisher

Shake well and apply 4-5 drops to desired pad. 
Prime pad with Pad Conditioner. Dab product out evenly across 2' x 2' section. 
Turn on machine away from paint to a setting in between 1000-1500 rpms to spread product. 
Using just the weight of the machine (no pressure) work area in 3-4 passes until compound becomes clear.
For final pass adjust speed setting to between 1200-1800 rpms.
Work until optical clarity is achieved.
Remove residue with clean microfiber cloth.


You might also like