使用這款混合劑來：
- 快速去除1500-2000磨蝕粒子造成的痕跡
- 去除中等程度漩渦痕跡、刮痕、氧化和其他缺陷
- 為下一個優化步驟做好準備
- 復修車頭燈，讓您在晚上安全駕駛
- 減少清潔塵埃，帶來最佳拋光體驗
為嚴重缺陷而設的中等研磨力
V34專門去除中等程度的漩渦痕跡、刮痕、氧化和泥沙痕跡。混合了光學級研磨粒子，能夠復修車漆瑕疵，再帶來光亮飾面效果。遞減式研磨粒子能夠精準地磨掉缺陷，讓您輕鬆優化！
光學級研磨科技帶給您升級清晰度
V34專為輕微氧化塑膠而設，只需一步就能回復車頭燈鏡片。獨特水性配方混合了先進滋潤功能，為您延長優化時限。只需配合雙重動力拋光機使用，V34就能去除車漆瑕疵，並恢復亮麗光澤！
[如何使用]
如使用雙重動力拋光機：
1. 搖勻拋光劑，在墊上塗上4-5滴
2. 在墊上加上柔順劑後，每次以61cm² 面積塗抹車身
3. 把拋光機力度調至1，以確保塗層均勻
4. 把拋光機力度調至5-6，配合適度壓力，來回擦拭表面2-3次
5. 用拋光機輕力擦拭表面，以作飾面
6. 用超細纖維毛巾清除表面殘留物
7. 請注意：使用產品前請先在一角測試產品效果
如使用旋轉式拋光機：
1. 搖勻拋光劑，在墊上塗上4-5滴
2. 在墊上加上柔順劑後，每次以61cm² 面積塗抹車身
3. 帶拋光機遠離車身，然後把力度調至1000-1500rpms
4. 不加壓力地來回擦拭表面3-4次，以混和塗層
5. 把拋光機力度調至1200-1800rpms，再次擦拭以作飾面
6. 擦拭至表面光亮清晰
7. 用超細纖維毛巾清除表面殘留物
需時：1-5小時
技術要求：高階
預備工序：清洗表面、去除污垢
所需工具：雙重動力拋光機或旋轉式拋光機、超細纖維或海綿拋光墊、超細纖維毛巾、六角拋光墊
Use This Compound To:
- Quickly remove 1500-2000 grit sanding marks
- Remove moderate swirls, scratches, oxidation, and paint defects
- Get the perfect base for next steps
- Restore your headlights for safest night driving
- Minimize dusting for the best polishing experience
Mid-Level Cutting & Finishing Power For Tough Paint Defects
V34 cuts away light to moderate swirls, scratches, oxidation, and wet sand marks. V34 is blended with optical-grade micro abrasives that remove paint imperfections and defects, then finish with the clarity and precision that perfectionists demand. The diminishing micro abrasives work fast with true-cut accuracy; there are no fillers, so the results you see are the true results you get.
Optical Grade Micro Abrasive Technology For Enhanced Clarity
V34 is the preferred cutting compound for lightly oxidized optical plastic and is the perfect one step polish to finish after wet-sanding faded and hazy headlights. The water-based formula is blended with advanced lubricants for extended work time. Use V34 with any dual action or rotary polisher to remove scratches and surface defects and restore luster and shine to any paint finish!
<How to Use>
Dual Action Polisher
1.Shake well and apply 4-5 drops to desired pad.
2.Prime pad with Pad Conditioner. Dab product out evenly across 2' x 2' section.
3.Turn on machine on paint to speed setting 1 to spread product.
4.Increase speed to 5-6 and using moderate pressure, work area in 2-3 passes until product becomes clear.
5.Follow with light pressure to finish.
6.Remove residue with a clean microfiber towel.
7.Please Note: Always try a test spot before use.
Rotary Polisher
Shake well and apply 4-5 drops to desired pad.
Prime pad with Pad Conditioner. Dab product out evenly across 2' x 2' section.
Turn on machine away from paint to a setting in between 1000-1500 rpms to spread product.
Using just the weight of the machine (no pressure) work area in 3-4 passes until compound becomes clear.
For final pass adjust speed setting to between 1200-1800 rpms.
Work until optical clarity is achieved.
Remove residue with clean microfiber cloth.
